Bosch eBike system error codes (Purion, Intuvia, Kiox, Nyon, before the smart system) · Bosch Purion, Intuvia, Kiox, Nyon

Error 423 on Bosch Purion, Intuvia, Kiox, Nyon

What it means + how to fix it From the manual

Quick answer

Error 423 on the Bosch Purion, Intuvia, Kiox and Nyon (before the smart system) means “eBike battery connection problem.” Most likely cause: the battery isn't switched on or fully seated, or its contacts are dirty. Try this first: turn it off and on again.

Try this first

Free, and each takes under 5 minutes.

Turn it off and on again
Check the battery's own switch or key
Reseat the battery

Code meanings vary by brand. The same number can mean different things on different displays and controllers. Check your bike's manual to confirm.

About the Bosch Purion, Intuvia, Kiox and Nyon (before the smart system)

Bosch prints this same table in the Purion (BUI215) MY2023 US manual (pages English 12 to 14). source
The same table is in the Intuvia (BUI255) MY2021 US manual (pages English 15 to 17). source
The same table is in the Kiox Online Version (BUI330) MY2020 US/CA manual (pages English 35 to 38). source
The same table is in the Nyon Online Version (BUI350) MY2021 US manual (pages English 66 to 69). Bosch notes code 430 does not apply to the BUI350. source
These displays belong to Bosch's older eBike system, not the smart system. The Bosch smart system (for example the Purion 200 and Kiox 400C) uses six-character error numbers instead. source
Bosch also lists "7xx" for faults in third-party parts, and "Display is blank" for an internal fault of the on-board computer. They are not single codes, so they are not in this list. source

In plain English

Some batteries have a management system (BMS) that reports to the controller over a data connection. This code means that connection isn't working. Make sure the battery is switched on and fully seated first. Anything beyond that is a job for a shop.

Step-by-step checklist

Work from the top. Steps go from free and easy to shop jobs. Switch the bike off before touching any connector. Tick each step as you go. Your progress is saved on this device.

1Turn it off and on againFree Switch the display off, wait 30 seconds, then switch it back on. If the code clears, note what you were doing when it appeared, in case it comes back.
2Check the battery's own switch or keyFree Many batteries have a key or power button of their own that must be on. Make sure it's fully turned or pressed.
3Reseat the batteryFree Switch off and slide or lift the battery out of its mount. Wipe any dirt off the metal contacts on the battery and the mount, then put it back until it clicks and locks.
4Fully charge the batteryFree Plug in the charger and charge until it shows complete (usually a green light), then switch on and test again.
5Did you just change a part?Moderate Displays, controllers and batteries must be a compatible match (the same communication protocol), not just share a plug. If the problem started right after you replaced something, put the old part back or check compatibility with the seller.
6Have the battery testedShop job A shop can test the battery and its protection circuit and tell you if it needs replacing. Never open the battery pack yourself.

Parts you might need

As an Amazon Associate I earn from qualifying purchases. These links go straight to Amazon.

Only buy a part if the free steps didn't fix it. Always match the voltage and connector type to your bike.

Electrical contact cleaner spray
Cleans dirt and corrosion from connector pins and battery contacts.
View on Amazon
Replacement e-bike battery
Only if a shop confirms your battery is worn out or faulty. Must match voltage, mount and connector.
Match your bike's model first. Ask a shop if unsure.

Still not fixed?

Pages to try next:

When it's time for a shop: if you've worked through every step and the problem is still there, take the bike to an e-bike shop. Bring your notes on when it happens, plus the code.

Words on this page: Controller BMS (battery management system)